Arduino Motor Control Car

 Arduino Motor Control Car Using L293H Bridge



//This will run only one time.


void steup ()

{

    pinMode (3, OUTPUT);

    pinMode (4, OUTPUT);

    pinMode (5, OUTPUT);

    Serial.begin (9600)

}

void loop()

{

    int reading = analogRead(A0);

    Serial.println (reading);

    int output = reading/100;

    digitalWrite (3, HIGH);

    digitalWrite (4, LOW);

    digitalWrite (5, output);

    delay (2000);

}

Comments

Post a Comment

Popular posts from this blog

Ultra Sonic Sensor

 Ultra Sonic Sensor Code int trigPin = 12; /* Trig pin of the sensor is connected to the 6th pin of Arduino */ int echoPin = 11;  /* The echo pin of the sensor is connected to the 7th Pin of the Arduino */ long Duration; //Duration   long Distance; //Distance   int leftMotor_1=3;  //motor 1 the first data entry is HIGH OR LOW int leftMotor_2=2;  //motor 1 the second data entry is HIGH OR LOW int rightMotor_1=4; //motor 2 the first data entry is HIGH OR LOW int rightMotor_2=5; //motor 2 the second data entry is HIGH OR LOW int leftMotor_pwm=6;  // motor 1 Speed ​​control is done with pwm input for                       // 0-255 analog PWM signal is sent in range int rightMotor_pwm=9; // motor 2 Speed ​​control is done with pwm input for                        // 0-255 analog PWM signal is sent in range void setup() {   for(int i=2;i<=9;i++){    pinMode(i, OUTPUT);}  //2-9 No ports are set as outputs   pinMode(trigPin,OUTPUT);   pinMode(echoPin,INPUT);      Serial.begin(9600); // loca
Read more

temperature LCD and DHT11

 Code for  temperature LCD and DHT11 /*  * temperature LCD and DHT11.c  *  * Created: 7/16/2020 7:41:41 PM  * Author : Daniel F Diaz Bayona  */  #include <avr/io.h> #include <stdlib.h> #include <stdio.h> #include "LCD16x2_4bit.h" #define DHT11_PIN 8 uint8_t c=0,I_RH,D_RH,I_Temp,D_Temp,CheckSum; //here we will set the pin to low and high //first the pin will be low then after 200ms delay it will show or be high void Request() { DDRD |= (1<<DHT11_PIN); PORTD &= ~(1<<DHT11_PIN); _delay_ms(200); PORTD |= (1<<DHT11_PIN); } //the following function will show th response of the sensor DHT11 void Response() { DDRD &= ~(1<<DHT11_PIN); while(PIND & (1<<DHT11_PIN)); while((PIND & (1<<DHT11_PIN))==0); while(PIND & (1<<DHT11_PIN)); } //this function will receive the data, check for received bit 0 or 1 //if the pulse is greater than 30ms //then it will set the logic or the PIN
Read more

SIP CAR Code Ultra Sonic

 ULTRASONIC SENSOR #include <Servo.h> #define speedPinR 9   //  RIGHT WHEEL PWM pin D45 connect front MODEL-X ENA  #define RightMotorDirPin1  22    //Front Right Motor direction pin 1 to Front MODEL-X IN1  (K1) #define RightMotorDirPin2  24   //Front Right Motor direction pin 2 to Front MODEL-X IN2   (K1)                                  #define LeftMotorDirPin1  26    //Left front Motor direction pin 1 to Front MODEL-X IN3 (  K3) #define LeftMotorDirPin2  28   //Left front Motor direction pin 2 to Front MODEL-X IN4 (  K3) #define speedPinL 10   // Left WHEEL PWM pin D7 connect front MODEL-X ENB #define speedPinRB 11   //  RIGHT WHEEL PWM pin connect Back MODEL-X ENA  #define RightMotorDirPin1B  5    //Rear Right Motor direction pin 1 to Back MODEL-X IN1 (  K1) #define RightMotorDirPin2B 6    //Rear Right Motor direction pin 2 to Back MODEL-X IN2 (  K1)  #define LeftMotorDirPin1B 7    //Rear left Motor direction pin 1 to Back MODEL-X IN3  K3 #define LeftMotorDirPin2B 8  //Rear le
Read more